Highlights

Overview
Following the ongoing evolution of the miniature market and demand for improved performance, ISCAR is launching a new PICCO line featuring excellent coolant supply. The new line consists of popular geometries of inserts and holders for a wide range of internal machining applications.

Inserts

• Inserts in existing geometries for turning, grooving, threading, chamfering, profiling and face grooving applications
• Coolant through supply close to the cutting edge for improved tool life and chip control
• All inserts are available in grade IC908
• Inserts with popular geometries are available as standards. Other geometries can be supplied upon request as specials
• Designations - PICCO R/L...N
• Clamping flat is on top of insert’s shank
• The new inserts do not fit into the older type PICCO or MG PCO bars

Holders


TEST REPORT
Application: Turning
Part material: SAE 4340
Bore diameter: 6mm
Cooling pressure: 10Bar

	ISCAR	ISCAR
Tool	PICCO ACE 16-5	PICCO 16-4-5N
Insert	PICCO R 050.5-20 IC908	PICCO R 050.5-20N IC908
Cutting speed Vc (m/min)	80	80
Feed rate f (mm/rev)	0.04	0.04
Depth of cut ap (mm)	0.12	0.12
Tool life (pcs/corner)	55	80

---

PICCO ACE-N
Holders for PICCO-JETCUT Inserts with Internal Coolant Channels
• Holders are suitable for right and left-hand PICCO inserts


PICCO-N (holder)
Holders for PICCO-JETCUT Inserts with Internal Coolant Channels
• Holders are suitable for right- and left-hand inserts, and boring bars


PICCO R/L 050, 053, 055-N (Turning)
Inserts with Internal Coolant Channel for Internal Turning and Chamfering
(1) Cutting depth maximum

PICCO R/L 050, 053, 055-N (Turning) (continued)
Inserts with Internal Coolant Channel for Internal Turning and Chamfering
(1) Cutting depth maximum

---

PICCO R/L 050-NC (Turning, with Chipbreaker)
Inserts with Chipformers and Internal Coolant Channel for Internal Boring and Profiling
• All left-hand inserts on request
(1) Cutting depth maximum

---

PICCO R/L 090-N (Turning 90°)
Inserts with Internal Coolant Channel for Internal Turning and Profiling
(1) Cutting depth maximum

---

PICCO R/L 090-N (Turning 90°)
Inserts with Internal Coolant Channel for Internal Turning and Profiling
(1) Cutting depth maximum

---

PICCO R/L 047-N
Inserts with Internal Coolant Channel for Internal Deep Profiling
• Left hand inserts on request
(1) Cutting depth maximum

---

PICCO R/LHD 050-N (Turning for Hard Steel)
Inserts with Internal Coolant Channel for Internal Turning and Chamfering of Hard Steel - up to 65 HRC
(1) Cutting depth maximum

---

PICCO R 050-N (Turning with CBN)
CBN Tipped Inserts with Internal Coolant Channel for Internal Turning, Profiling and Chamfering of Hard Steel
• It is not recommended to use coolant when machining with CBN tipped tools
• Available on request only
(1) Cutting depth maximum

---

PICCO R/L 080-N (Back Turning)
Inserts with Internal Coolant Channel for Internal Back Turning
(1) Cutting depth maximum

---

PICCO R/L 002-007-N (Grooving and Turning)
Inserts with Internal Coolant Channel for Internal Grooving and Turning
• All carbide bars with sharp corners
(1) Cutting depth maximum

PICCO R/L 002-007-N (Grooving and Turning) (continued)
Inserts with Internal Coolant Channel for Internal Grooving and Turning
• All carbide bars with sharp corners
(1) Cutting depth maximum

---

PICCO R/L 004-007-N (Full radius)
Full Radius Inserts with Internal Coolant Channel for Internal Profiling
(1) Cutting depth maximum

---

PICCO R/L 004-007-N (Full radius)
Full Radius Inserts with Internal Coolant Channel for Internal Profiling
(1) Cutting depth maximum

---

PICCO R/L 070-N (Back Chamfering)
Back Chamfering Inserts with Internal Coolant Channel for Pre-Parting Operations
• All carbide bars with sharp corners
(1) Cutting depth maximum

---

PICCO R/L 520-N (Chamfering)
Inserts with Internal Coolant Channel for Internal Chamfering
• Left hand inserts on request

---

PICCO-010/610-N (Face Grooving)
Inserts with Internal Coolant Channel for Face Grooving
• Only right-hand inserts are available as standard
• All carbide bars with sharp corners
(1) Minimum axial grooving diameter

---

PICCO-010-N (Full Radius for Face Grooving)
Inserts with Internal Coolant Channel for Round Profile Face Grooving
• Only right-hand inserts are available as standard, left-hand inserts on request
(1) Minimum axial grooving diameter

---

PICCO-620-N (Face Grooving along Shaft)
Inserts with Internal Coolant Channel for Grooving along Shaft Dmin 6 mm
• Only right-hand inserts are available as standard, left-hand inserts on request
• All carbide inserts are with sharp corners
(1) Minimum axial grooving diameter

---

PICCO-015-N (Face Grooving)
Inserts with Internal Coolant Channel for Deep Face Grooving
• Only right-hand inserts are available as standard, left-hand inserts on request
• All inserts are with sharp corners
(1) Minimum axial grooving diameter

---

PICCO-016/020-N (Face Grooving)
Inserts with Internal Coolant Channel for Deep Face Grooving
• All inserts have two coolant holes which may be used with coolant pressure up to 100 bars
(1) Minimum axial grooving diameter

---

PICCO-55°-N (55° Threading)
Inserts with Internal Coolant Channel for 55° Internal Threading Profile
• All mini-bars have sharp corners
(1) Threads per inch maximum
(2) Threads per inch minimum

---

PICCO R/L60°-N (60° Threading)
Inserts with a 60° Internal Thread Profile and Internal Coolant Channel for 2.4 mm Min. Bore Diameter
(1) Thread pitch

---

The NPA19-2019's pdf file: View (PDF) or Download (ZIP)